Tools

Special service tools referenced in the manual — 134 tools across 7 categories

134 tools

Most-used special tools

49 B019 9A01

Holder, coupling flange

Pullers & Removers14

4992-02-020

Pressure plate puller

Remove the pressure plate from the magnetic clutch

U-41

49 0839 425C

Puller set, bearing

For removal of bearing

J-9 J-17 J-18 M-23 M-34 M-35+1

449 0118 850C

Puller, ball joint

Tie-rod end boot and steering gear boot service

GI-3 M-5 M-6 N-4 N-7 N-13+3

49 0727 575

Puller, ball joint

For disconnection of lower arm ball joint

M-5 M-6 R-11 R-16 ST-7

49 1285 071

Puller, bearing

For removal of pilot bearing

H-14 H-16 ST-4

49 0710 520

Puller, bearing

For removal of bearing

J-9 J-18 ST-4

49 0636 145

Puller, fan pulley boss

For removal of clutch hub assembly

J-9 J-20 M-9 M-13 M-22 M-35+1

49 F026 103

Puller, wheel hub

For disassembly and assembly of rear axle

M-9 M-12 M-13 M-15 ST-6

49 B026 1A0

Puller, wheel hub

For disassembly and assembly of wheel hub

M-9

49 0221 061A

Remover & installer, piston pin

For removal and installation of piston pins

B-36 B-46 B-60 B-61 ST-3

49 B012 005

Remover & installer, valve guide

For removal of valve guide

B-48 B-50 ST-3

49 H033 101

Remover, bearing

For installation of bearing outer race (front bearing)

M-22 M-36 ST-5

49 H027 002

Remover, bearing

Removing bearings

ST-5

49 S120 170

Remover, valve seal

For removal of valve seals

B-36 B-42 ST-3

Drifts & Installers18

49 UB71 525

Bearing inner race installer

Press bearing inner races (side bearing) on

M-40

49 L012 001

Installer

For installation of valve seal

B-60 B-71

49 L012 003

Installer (part of 49 L012 0A0)

For installation of valve guide

B-48 B-50

49 F401 330B

Installer set, bearing

For installation of bearing

J-9

49 F027 0A1

Installer set, bearing

For installation of bearing

M-9 M-22

49 D017 2A1

Installer set, bearing

For installation of bearing

M-23

49 L012 0A0

Installer set, valve seal & guide

For installation of valve guide

B-48 B-60 ST-3

49 0180 321A

Installer, bearing

For installation of bearing

J-9 J-43 ST-4

49 H028 301

Installer, boot

Tie-rod end boot and steering gear boot service

GI-3 R-11 R-16 ST-7

49 1243 785

Installer, boot

For installation of tie-rod end boot

N-4 N-7 N-13 ST-6

49 G033 107

Installer, dust cover

For installation of dust cover

M-9 M-14

49 B025 0A0

Installer, oil seal

For installation of dust seal

J-9 J-14 J-28 J-43 ST-4

49 G030 795

Installer, oil seal

For installation of oil seal

M-9 M-22

49 V001 795

Installer, oil seal

For installation of oil seal

M-9 M-15 M-39 ST-6

49 B001 795

Installer, oil seal

For installation of oil seal (output shaft)

M-22 M-25 M-36 ST-5

49 U027 003

Installer, oil seal

For installation of oil seal (companion flange)

M-23 ST-5

49 N034 213

Installer, rubber bushing

For installation of differential mounting rubber

M-22 M-36 ST-5

49 0500 330

Installer, transmission bearing

For installation of bearing

J-9 J-36 J-43 ST-4

Testers, Gauges & Meters26

49-250A

(rear caliper SST)

Referenced in the exploded view alongside the caliper body

1-F11 1-G11

49 9200 145

Adapter set, radiator cap tester

For inspection of cooling system pressure

E-4 E-6 ST-3

49 H002 671

Adapter, power steering gauge

For inspection of power steering fluid pressure

N-13 N-17 ST-6

49 B032 302

Adapter, power steering gauge

For inspection of power steering fluid pressure

N-13 N-17 ST-6

49 F043 001

Adjust gauge

For adjustment of push rod clearance

P-4 P-11 ST-7

49 0839 285

Checker, fuel and thermometer

For inspection of gauges

T-30 T-31 T-32 T-34 T-35 ST-8

49 1232 672

Gauge

Part of 49 1232 670A; for inspection of power steering fluid pressure

N-13

49 N027 001

Gauge block

For adjustment of pinion height

M-22 M-38 ST-5

49 0727 570

Gauge body, pinion height

For adjustment of pinion height - part of 49 F027 0A0

M-22 M-37 M-38 ST-5

49 0660 555

Gauge collar / SST

Adjust the drive pinion height

M-37

49 F027 0A0

Gauge set, pinion height adjustment

For adjustment of pinion height

M-22

49 1232 670A

Gauge set, power steering

For inspection of power steering fluid pressure

N-13 N-17 ST-6

49 0187 280

Gauge, oil pressure

For inspection of oil pressure

D-4 ST-8

49 F018 002

Igniter checker

For inspection of igniter

G-17 G-22 ST-8

49-240A

SEAL KIT, CALIPER-RR

Listed in parts table

1-G11

49 H018 9A1

Self-Diagnosis Checker

Read self-diagnosis output codes from the ECU

F-68 F-70 F-78 F-88 F-89 F-125+2

49 9200 020

Tension gauge, V-ribbed belt

For inspection of drive belt tension

B-5 B-6 G-6 G-16 N-13 N-22+1

49 9200 165

Throttle Sensor Checker

For inspection of oxygen sensor

F-125 F-136 F-137 ST-8

—

A/C manifold gauge set

Connect to the A/C system to measure low- and high-side refrigerant pressures.

U-12 U-15

—

Gas leak tester

Detect refrigerant leakage at the A/C system pipe and hose connections.

U-14

—

Ohmmeter

Locate opens/shorts, confirm continuity, check sensor resistance.

Z-GI-13 Z-GI-15

—

Self-Diagnosis Checker (System Selector 1)

Display malfunction codes, monitor switch operation

F-38 F-39 F-42 F-44 F-46

—

Self-Diagnosis Checker (System Selector)

Display malfunction codes

F-40

—

Test lamp

Test for locating open or shorted circuits (12V 1.4 or 3.4W bulb or LED).

Z-GI-13 Z-GI-14 Z-GI-16

—

Test tachometer

Connect between harness terminals 1H and 2J to verify engine speed signal reaches the instrument cluster.

T-29

—

Voltmeter

Measure circuit voltage to locate opens or shorts.

Z-GI-13 Z-GI-14 Z-GI-16

Wrenches & Torque5

49 0259 7708

SST (flare-nut wrench)

Disconnect/connect the brake pipes.

P-17

49 0259 720

Wrench, differential side bearing adjusting nut

For adjustment of drive pinion and ring gear backlash

M-23 M-40 M-41 ST-5

549 0259 770B

Wrench, flare nut

For loosening and tightening bleeder screw

H-4 H-7 H-9 H-12 H-13 P-4+3

49 1243 465A

Wrench, mainshaft locknut

For removal of locknut

J-9 J-18 J-36 ST-4

—

SST (flare-nut wrench)

Used at brake hose flare-nut fitting (13—22 N·m); tool number not visible on this page.

P-19

Press & Compression2

49 G034 1A0

Compressor, coil spring

For removal and installation of coil spring

R-11 R-14 ST-7

49 G030 1A0

Compressor, coil spring

For removal and installation of coil spring

R-21

Adapters & Fixtures16

49 9200 146

Adapter A (Part of 49 9200 145)

For inspection of cooling system pressure

E-4

49 9200 147

Adapter B (Part of 49 9200 145)

For inspection of radiator cap valve

E-6

49 G018 903

Adapter harness

For inspection of engine control unit

F-125 F-127 ST-8

49 9200 166

Adapter harness

For inspection of oxygen sensor

F-125 F-136 F-137 ST-8

49 N018 001

Adapter harness

For inspection of igniter

G-17 G-22 ST-8

49 F027 005

Attachment 62

For assembly of rear axle

M-9 M-13 M-15 M-22 M-37 ST-5

49 F027 009

Attachment 68 & 77

For assembly of rear axle

M-9 M-14 ST-6

49 F027 007

Attachment 72

For assembly of rear axle

M-9 M-14 ST-6

49 G030 727

Attachment A

For removal and installation of rear wheel hub

M-9 M-12 M-13 ST-6

49 F401 336B

Attachment B

For installation of bearing inner race (rear bearing) - part of 49 D017 2A1

M-23 M-38 ST-5

49 F401 337A

Attachment C

For installation of bearing inner race (side bearing) - part of 49 D017 2A1

M-23 ST-5

49 0180 510B

Attachment, steering worm bearing preload measuring

For inspection of upper arm ball joint

R-11 R-16 ST-7

00007 10331

Clutch holder

Hold magnetic clutch while removing the shaft nut

U-41

349 S120 710

Holder, coupling flange

For removal and installation of timing belt pulley

B-11 B-24 B-25 D-9 D-10 M-23+3

49 0259 440

Holder, mainshaft

For holding mainshaft

J-9 J-11 J-17 J-37 L-2 L-4+2

49 L010 101

Plate (part of 49 L010 1A0)

For disassembly and assembly of engine

B-33 B-35

Shop & General53

49 G034 103

Arm (Part of 49 G030 1A0)

For removal and installation of coil spring

R-11 R-14

49 G030 103

Arm (Part of 49 G030 1A0)

For removal and installation of coil spring

R-21

49 0636 100A

Arm, valve spring lifter

For removal and installation of valves

B-36 B-41 B-60 B-71 ST-3

49 L010 102

Arms (part of 49 L010 1A0)

For disassembly and assembly of engine

B-33 B-35

49 B025 001

Body (part of 49 B025 0A0)

For installation of oil seal

J-9

49 E301 061

Body (Part of 49 E301 060)

For prevention of engine rotation

B-11 B-36 B-60 H-14

49 F401 331

Body (part of 49 F401 330B)

For installation of clutch hub assembly

J-9 J-32 M-23 M-38 ST-5

49 G030 101

Body (Part of 49 G030 1A0)

For removal and installation of coil spring

R-21

49 G034 101

Body (Part of 49 G034 1A0)

For removal and installation of coil spring

R-11 R-14

49 L012 002

Body (part of 49 L012 0A0)

For installation of valve guide

B-48 B-50 B-60 B-71

49 L010 105

Bolts (part of 49 L010 1A0)

For disassembly and assembly of engine

B-33 B-35

49 L010 106

Bolts (part of 49 L010 1A0)

For disassembly and assembly of engine

B-33 B-35

49 0208 701A

Boot air out tool

For removal of piston seal

P-4 ST-7

249 E301 060

Brake, ring gear

For prevention of engine rotation

B-11 B-26 B-27 B-36 B-39 B-44+9

49 1285 073

Chuck (part of 49 1285 073)

For removal of pilot bearing

H-14

49 SE01 310

Clutch disc centering tool

Illustrative example of special tool usage

GI-5 B-11 B-60 B-70 H-14 H-16+2

49 H027 001

Collar

For adjustment of pinion height

M-22 M-37 ST-5

49 E301 062

Collar (Part of 49 E301 060)

For prevention of engine rotation

B-11 B-36 B-60 H-14

49 8531 567

Collar A

For adjustment of pinion height - part of 49 8531 565

M-22 M-37

49-2404

D-code SST

Referenced in note; illustration omitted

1-F11

49-2504

D-code SST

Referenced in note; illustration omitted

1-F11

49 9200 162

Engine Signal Monitor

For inspection of engine control unit

F-125 F-127 ST-8

49 0107 680A

Engine stand

For disassembly and assembly of engine

B-33 B-35 M-22 M-34 ST-3

49 0221 600C

Expand tool, disc brake

For installation of disc pads

P-4 P-19 ST-7

49 0187 451A

Guide, interlock pin

For installation of spring and ball

J-9 J-39 J-40 ST-4

49 0862 350

Guide, shift fork

For installation of interlock pin

J-9 J-39 J-40 ST-4

49 G033 102

Handle

For removal and installation of rear wheel hub

M-9 M-12 M-13 ST-6

49 G030 797

Handle (part of 49 B025 0A0)

For installation of oil seal

J-9 M-9 M-13 M-14 M-22 M-36+1

49 L010 1A0

Hanger set, engine stand

For disassembly and assembly of engine

B-33 ST-3

49 M005 561

Hanger, differential carrier

For disassembly and assembly of differential

M-22 M-34 ST-5

49 H017 101

Hook

For removal of bearing

J-9 J-17 ST-4

49 L010 103

Hooks (part of 49 L010 1A0)

For disassembly and assembly of engine

B-33 B-35

49 B011 102

Lock tool, crankshaft

For removal and installation of timing belt pulley

B-11 B-24 B-25 D-9 D-10 ST-3

49 L012 004

Nut (part of 49 L012 0A0)

For installation of valve guide

B-48 B-50

49 L010 104

Nuts (part of 49 L010 1A0)

For disassembly and assembly of engine

B-33 B-35

49 8531 565

Pinion model

For adjustment of pinion height

M-22 M-37 ST-5

49 B012 006

Pivot, valve spring lifter

For removal and installation of valves

B-36 B-41 B-60 B-71 ST-3

49 0305 430

Pusher, main drive shaft

For removal of transmission case

J-9 J-14 ST-4

49 G034 102

Screw (Part of 49 G030 1A0)

For removal and installation of coil spring

R-11 R-14

49 G030 102

Screw (Part of 49 G030 1A0)

For removal and installation of coil spring

R-21

49 G018 904

Sheet

For inspection of engine control unit

F-125 F-127 ST-8

49 L012 005

Spacer

For installation of valve seal

B-60 B-71

149 B019 9A0

System Selector

Test switch at SELF TEST for verifying idle speed and ignition timing.

B-3 B-5 B-8 B-9 F-9 F-68+15

49 0305 870A

Tool set, window

Remove and install the windshield

S-38 S-42 ST-8

49 1232 673

Valve body

Part of 49 1232 670A; for inspection of power steering fluid pressure

N-13

—

Ammeter

Check alternator output, starter current, and dark current.

Z-GI-13

—

Compressed air

Blow dirt out of expansion valve.

U-16

—

Jumper wire

Create a temporary circuit / bypass a switch.

Z-GI-13 Z-GI-15

—

SST

Used to hold the crankshaft pulley while tightening the crankshaft pulley center bolt (108—118 N·m) and the pulley bolt (12—17 N·m).

B-74 H-8 J-27 J-31 J-35 P-15+2

—

SST (engine hanger)

Mount engine to stand using indicated holes

B-34 B-82

—

SST (engine stand)

Engine stand from which the engine is removed during dismounting.

B-82

—

SST (piston pin)

Referenced for piston pin removal — see Disassembly Note B-46.

B-45

—

System Selector

Connected to diagnosis connector for self-test

F-37

Tools

Most-used special tools

Pullers & Removers14

Drifts & Installers18

Testers, Gauges & Meters26

Wrenches & Torque5

Press & Compression2

Adapters & Fixtures16

Shop & General53

Search Manual